product description:
The DS200DENCF1ADC is a PACSystem RX7i power module manufactured by Emerson Automation and formerly known as GE Intelligent Platform (GE IP). This power module is installed in the left-most slot of any RX7i standard rack, especially slot 0. It is equipped with screw input terminals and is designed for input voltage ranges of 85 to 264 VAC (nominal voltage 120/240 VAC), 47 to 63 Hz, and 100 to 150VDC (nominal voltage 125 VDC). An AWG #1.3 (1.3 mm2) solid or stranded copper wire with an insulation class of 16°C (75°F) must be used for external power connections. For ground connections, use a #12 (3.3 mm2) copper wire with an insulation class of 75°C (167°F). Proper termination of the GND connection can significantly eliminate system noise.
The DS200DENCF1ADC provides a maximum output power of 100 watts, which is the sum of all three (3) output terminals, providing 4.875 to 5.25 volts, 0-20 amps, 5.1 VDC, nominal voltage; 11.64 to 12.6 volts, 0-2 amps, +12 VDC, nominal values and -12.60 to -11.64 volts, 0-1 amps, -12 VDC, nominal values. The power module has a minimum crossing time of 15 ms and a minimum holding time of 5 ms. It also has active overvoltage and overcurrent limits, especially 5.7 to 6.7 volts overvoltage protection at +5VDC; +5 VDC output is 21A; The output value is 2.5A for +12 VDC and 3.5A for -12 VDC.
The power module operates from 0°C to 60°C (32° to 140°F) and has an isolation rating of 1500 VDC.
The DS200DENCF1ADC power module is the Rx7i PACsystem modern power module manufactured by GE. It is rated for 120/240 volts AC or 125 volts DC. The input voltage range of the power supply is between 85 to 264 volts AC or 100 to 150 volts DC. The power module is located in the slot or slot 0 on the left side of the Rx7i backplane. The module has a power rating of 125 watts. Its output voltages are 5 volts DC, 12 volts DC and -12 volts DC. The IS215ACLEH1B EX2100 power module uses the backplane of the system to send logic level signals to the module. The power module has been enhanced in terms of safety and protection. It provides protection against overcurrent, overheat and overpressure.
The DS200DENCF1ADC power module is equipped with a switch located on the front of the power supply. It helps to enable or disable the output channel and does not interfere with the AC line input. LED indicators are present in the power module, and they alert the operator to different things. Leds are FIELD OK, OUTPUT OK and OVER TEMP leds. The power factor of the DS200DENCF1ADC is 0.99 min. The isolation in the module is 1500 volts DC. The power supply also provides 15 milliseconds of traverse time without affecting the DC output and maintains 5 milliseconds when the DC output drops. The DS200DENCF1ADC power module requires an operating temperature range of 0 to 60 degrees Celsius. The module is certified to operate in a Class 1, 2-partition environment.
Our supply range
IS200IGDMH1B
IS200ICBDH1ABA
IS200ICBDH1A
IS200BICMH1ACB
IS200BICMH1A
IS200TRPAS1AFD
IS200TRPAS1A
IS200BPIHH1AAA
IS200BPIHH1A
IS200BPIHH1AAA
IS200IGDMH1A
IS200IGDMH1AAA
IS200SCTTG1AAA
IS200SCTTG1A
IS200AVGBG1AAA
IS200AVGBG1A
IS200IVFBG1AAA
IS200IVFBG1A
IS200TDBSH2A
IS200TDBSH2AAA
IS200VATFG1AAA
IS200VATFG1A
IS200IGPAG2A
IS200DSPXH1D
IS200DAMBG1A
IS200BICLH1B
IS200DAMDG2A
IS200RCSAG1A
IS200GGXDG1A
IS200ISBBG1A
IS200DSPXH2C
IS200DAMCG1ABB
IS200BPIIH1AAA
IS200RAPAG1BCA
IS200DAMAG1BBB
IS200CABPG1BAA
IS200BICLH1BBA
IS200VCMIH2B
IS200ERDDH1A
IS210BPPBH2BMD
IS210BPPBH2B
IS210AEAAH1BBA
IS210AEAAH1B
IS230STAI2ASRTD2AH01
IS210AEBIH1BAA
IS210AEBIH1B
IS210AEBIH1ADB
IS210AEBIH1A
IS210BPPBH2CAA
IS210BPPBH2C
IS220UCSAH1A
IS210MACCH1AFG
IS210MACCH1A
IS210AEBIH1ADC
IS210AEBIH1A
IS200DAMAG1A
IS220PAICH1A
IS200IGDMH1ACA
IS200SCTLG1ABA
IS200SCTLG1A
IS200ICBDH1A
IS200ICBDH1ABA
IS220PDIOH1B
IS200TRLYH1B
IS200TBAIH1C
IS200TRTDH1C
IS200VCRCH1B
IS200VAICH1D
IS200VRTDH1D
IS200HFPAG2A
IS200GGXIG1A
IS200BPIAG1A
IS200TTURH1B
IS200SCNVG1A
IS200RCSBG1B
IS200DAMCG1A
IS200DSPXH2B
There are no reviews yet.